|
About · The best of both worlds: simple, easy to operate centralized setback programming and room by room temperature control · Fits the following models: Alto, Mezzo, Solo, Allegro, Allegro-Duo, Opera and Tenor · Controls up to 20 Convectair heaters connected by a signal wire · Preprogrammed or customized 24 hr schedule, 7 days a week · Frost protection setting · May be locked in the heater socket · Two-year guarantee against manufacturing & material defect |
|
Service@heatersheatersheaters.com Or call us at (888) 256-1566 |
|
To contact us: |
|
HeatersHeatersHeaters by UMCI 3427 North Clinton Street PO Box 5186 Fort Wayne, Indiana 46895 Copyright © 2008 UMCI. All Rights Reserved
|
|
The Programmer module manages your household heating comfort zones. For example, set the temperature to 68°F at daytime and then, have it drop down automatically to 61°F at bedtime.
It controls scheduled changes in temperature via special wiring (pilot-wire model) or powerline carrier technology with existing wiring (powerline carrier model).
The figure above shows the wiring of nine Convectair heaters in two different zones with 2 Programmer FP modules. |
|
7392-FP Single Unit Programmer |
|
7392-ECP Base Module |
|
7392-RCP Receiver Module |
|
$110.00 |
|
$219.00 |
|
$100.00 |
|
USE |
|
|
|
Designed to be inserted into the control panel of Alto (7384), Mezzo (7383), Solo (7382), Tenor (7715) and Opera (7720). Controls up to 20 Convectair heaters - apart from the Apero (7358) and Soprano (7808)-connected by a signal wire or by using powerline carrier technology. |
|
|
|
|
OPERATION |
|
|
|
Can be programmed after 15 minutes of full charging in a heater connected to a power source. No batteries required. May be programmed directly on the heater or removed from the outlet. The programmer module becomes operational once it is reinserted in its outlet. May be locked in the heater outlet. |
|
|
|
|
LCD DISPLAY |
|
|
|
Continuously displays current time, day, heating mode (Comfort, Economy or Frost Protection), daily program and hourly status; displays hour, day and program while settings are being entered. |
|
|
|
|
PROGRAMMING |
|
|
|
Choice of 7 pre-selected programs or a customized hour-by-hour Comfort or Economy program for each day of the week and Frost protection mode. The Programmer module lets you override current program centrally or individually for each heater. Simple, easy programming instructions are found directly on the Programmer module. In case of power failure, the Programmer module will keep its charge for 10 hours. Beyond that, only the time and day must be reset. All pre-selected and custom programs are saved indefinitely. |
|
|
|
|
WIRING |
|
|
|
For single-heater programming: install the Convectair unit using a standard 2-conductor cable.
· 7329FP: Programmable pilot-wire module. Each module can control scheduled temperature variations up to 20 compatible heating units -see list below- Wiring requirements: 3-conductor cable (type NM-B, 12/3 WG) from the module to the units.
· 7392 ECP and RCP: Programmable powerline carrier unit consisting of a transmitter module (ECP) and a receiver module (RCP). Each ECP module can control scheduled temperature variations up to 20 heating units equipped with receiver modules (RCP) -see list below- Maximum of 3 ECP modules per home (3 heating zones). No special wiring required
Master units compatible with FP, ECP, or RCP modules: Solo (A7382), Mezzo (A7383), Alto (A7384), Allegro (A7300), Tenor (A7715), Opera (A7720) and Allegro Duo (7792). Remote units that can receive FP signals: All Convectair units, with the exception of Soprano (A7808) and Apero (7358).
Note: Any heater equipped with a RCP module can in turn relay a FP signal to other remote units (contact us for more information).
All heaters linked to a Programmer module make up a comfort zone. In Comfort and Economy modes, the temperature of each individual heater in zone may be adjusted for ideal comfort and optimal energy savings. |
